WeChat ID
aaronpk_tv
#triplex
-
We did the top side coat of Rubio Monocoat today! Looks so good! 💯
-
Cleaned up and did the first side of the Rubio Monocoat for the live edge slab! I think it turned out pretty good!
-
I decided today would be a good day to hang the vertical monitor that will eventually be the home automation dashboard. I found a monitor that fills the available space. Next I need to get an HDMI over ethernet extender so I don't have to put a raspberry pi on the wall.
-
Today is mini split day! They are starting to put in all the mini splits for the units!
-
First dip in the tub now that it's actually hot
-
Got the hot tub up and running!
-
Worked on a bunch of house projects today!
- Finished tidying up the low voltage panels for Units A and B
- Fixed the electronic door latch for Unit A
- Installed a new camera facing the street to watch for delivery vehicles and such
- Terminated the network jack at the hot tub
- Prepped a bunch of the hot tub wiring and started draining it
-
Unsurprisingly, it took me literally all day to get the network closet back up and running! But this time it is much more neatly organized.
I added a 12-port patch panel in the corner that all the building runs terminate into. Half of these were from the 2019 studio buildout, the other half I've added over the years, with pretty messy cable runs through the space. Now they are all neatly tucked inside the wall and terminated into this patch panel!
I then started rebuilding the rack, and made custom length cables for the 12 connections. One end is an rj45 jack, the other end is a keystone connector for the rack patch panel.
By the end of the day I was able to get all the gear back in the rack! I know it still looks a bit messy but believe me this is far better than it was before I started this!
-
Busy day at the triplex today!
The plumber came to finish up everything inside:
- Hung the mount for the bathtub spray head
- Attached the mixer valve for the shower
- Attached the pole for the shower head
- Moved the spigot for the roof mister
- Moved the sewer line for the loft to the lower sewer line the guys added a few months ago. That means no more pump for the laundry room sink and washer needed anymore!
I also found cat5e wires in the utility room closet that were for the phone jacks in the loft, so I traced them and terminated them with network jacks so now there’s a network jack in the loft! Why didn’t I find this years ago? I just assumed it was cat3 wiring because it was for a phone.
I’m also tackling some loose ends in the house, a few dangling network jacks I hadn’t finished yet.
The drywaller finished the utility closet so I can put everything back together!
Oh and the cleanup crew came and took out a bunch of trash and also took the temporary power pole!
-
Today I prepped for the drywall crew to come and patch up the walls in the utility closet. I moved the network wires inside the wall to a new location so there will be less exposed wires in the inside, and also moved the fiber cable into the ceiling so it isn't awkwardly draped through the room.
-
Today is the day! We are finally getting the permanent power hookup to the new house! I can't even believe how long I've been waiting for this. This is super important because it unblocks a bunch of other stuff from happening in order to finish the project.
It looked like it almost wasn't going to happen there for a bit, but the crew pulled through! A very quick tree trim, an extra supply run to get thicker wire, and a quick reroute of the conduit for the main line and we're back in business.
Also I just think it's really funny that the guy from the power company just ripped the meter off the side of the building while everything inside was still powered on. Seems like you might want to disconnect the load at the breaker before pulling potentially 200 amps off the wall but hey that's not my job.
-
This week I need to tackle this project! I need to remove everything in the utility room so the electricians can run a new main power line through the ceiling. Capturing this for the "before" photo.
-
Still working on variations of the shed. This version is an attempt to build it as a proper "shed", meaning 120 sq ft and only 15' tall. The current question is whether we can run a sprinkler pipe so we can do the door on the driveway side.
-
Sanded down the table with 60-100-120-150-220 grit, and did the small spot epoxy on the other side. If it's not raining tomorrow we can finish sanding and maybe get the finish on!
-
Office cabinet handles installed!
-
We did it! Woke up at midnight and went out to do the final pour!
-
Third layer at 7:30pm, but will need to come back after midnight for the final layer!
-
Second layer done at 4pm
-
First layer of epoxy poured. It needs 4 hours to set between layers
-
Did all the prep work for this live edge table and got it cut down to size, but then realized we bought the wrong kind of epoxy so the pour has to start tomorrow.
